MiFab logo

Serving all of the USA, Canada, Australia and the Middle East, MIFAB can provide you with the quality, engineered plumbing and drainage solutions you need. Innovative product designs save the installer time and material cost and provides the owner with higher quality cast stainless steel drains and cleanouts for the same cost as the industry standard nickel bronze. Contact us today to learn more.

All Categories  > Fixture Carriers

 

Results Per Page  
Returned 66 Results
Browse Pages :   1 | 2
Page 1 of 2
  • Click for specsheet

    Click for downloads

    List Prices

     

    You have told us how frustrating and expensive it is when the ADA water closet is less than 18” from the center to the finished wall.

    You can now offset the fixture without having to tear out the car rier! The MC-10 Series is tested with the “Shift and Lift” offset hardware package to support a 500 lb. Load with the rear anchor support.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-10 single, horizontal, adjustable water closet carrier with lacquered cast iron fitting, 4" (102) no hub waste and 2" (51) no hub vent connection, lacquered cast iron gasketed, adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts, and rear anchor tie down support.
    FUNCTION: Used with off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixture is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

  • Click for specsheet

    Click for downloads

    List Prices

     


    SPECIFICATION: MIFAB® Series MC-10-HS (Specify -L for left or -R for right design) single, horizontal, adjustable hub and spigot water closet carrier with lacquered cast iron fitting, 2” (51) vent connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

     

    Function:Used with off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixture is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

     

    Note:10 1/2” (267) minimum space required between front of foot and rear of anchor support. 8” (203) minimum in wall space required between back of rear anchor support and back of in wall foot supports. Note: Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

     

  • Click for specsheet

    Click for downloads

    List Prices

     

    Specification: MIFAB Series MC-10-HDX, 1000lb. Carrier Support complies with all applicable requirements of ASME A112.6.1M up to a 1000lb. (454kg) load. This support is used in concert with the standard lacquered cast iron adjustable faceplate, lacquered cast iron waste fitting, adjustable ABS nipple, hardware and finishing kit.

    Function: Used to provide additional support capability in excess of standard carrier loading. The -HDX option is for use with all MC-10, MC-12 and MC-13 series fixture carriers when up to a 1000lb. static load is anticipated. System comes with adjustable support frame and rear anchor tie down. The feet and rear anchors are bolted to the floor using anchors capable of achieving the specified "pull-out" force (750lbs./340kg.) in which the rear anchors are mandatory for secure installation.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-10D double, horizontal, adjustable water closet carrier with lacquered cast iron fitting, 4" (102) no hub waste and 2" (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors, and polished chrome plated finishing cap nuts.

  • Click for specsheet

    Click for downloads

    List Prices

     


    SPECIFICATION: MIFAB® Series MC-10D-HS double, horizontal, adjustable hub and spigot water closet carrier with lacquered cast iron fitting, 2” (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

     

    Function:Used with back to back off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The closet carrier is completely concealed within the wall and supports the load of the fixtures through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixtures is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

     

    Note:14 1/2” (368) minimum space required between front of foot supports. 9” (229) minimum in wall space required between back of in wall foot supports.

     

    Note:Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

     

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-10-EXT (Specify L for left or R for right design) single, horizontal, adjustable, high rough-in water closet carrier with lacquered cast iron fitting, 4" (102) no hub waste and 2" (51) no hub vent connection, lacquered cast iron gasketed, adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts, and rear anchor tie down support.

  • Click for specsheet

    Click for downloads

    List Prices

     


    SPECIFICATION: MIFAB® Series MC-10-EXT-HS (Specify L for left or R for right design) single, horizontal, adjustable, high rough-in water closet carrier with lacquered cast iron fitting, 4” (102) hub and spigot waste, 2” (51) hub and spigot vent connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

     

    Function:Used in the middle of horizontal batteries where the water closet must be elevated 3” (76) higher than the normal roughin height to accommodate fixtures for wheelchair users. The elevated inlet flange permits the water closet to be installed at any position in the battery. Typical with off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixture is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

     

    Note:10 1/2” (267) minimum space required between front of foot and rear of anchor support. 8” (203) minimum in wall space required between back of rear anchor support and back of in wall foot supports. Note: Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

     

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-10D-EXT double, horizontal, adjustable, high rough-in water closet carrier with lacquered cast iron fitting, 4" (102) no hub waste and 2" (51) no hub vent connection, lacquered cast iron gasketed, adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors, and polished chrome plated finishing cap nuts.

  • Click for specsheet

    Click for downloads

    List Prices

     


    SPECIFICATION: MIFAB® Series MC-10D-EXT-HS (Specify L for left or R for right design) single, horizontal, adjustable, high rough-in water closet carrier with lacquered cast iron fitting, 4” (102) hub and spigot waste, 2” (51) hub and spigot vent connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

     

    Function:Used in the middle of horizontal batteries where the water closet must be elevated 3” (76) higher than the normal roughin height to accommodate fixtures for wheelchair users. The elevated inlet flange permits the water closet to be installed at any position in the battery. Typical with off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixture is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

     

    Note:10 1/2” (267) minimum space required between front of foot and rear of anchor support. 8” (203) minimum in wall space required between back of rear anchor support and back of in wall foot supports. Note: Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

     

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-10-27 (Specify L for left or R for right design) single, horizontal, adjustable, water closet carrier with lacquered cast iron fitting, 4" (102) no hub waste, 2" (51) no hub vent connection, 2" (51) no hub auxiliary inlet connection, lacquered cast gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts, and rear anchor tie down support.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-10D-27 double horizontal adjustable water closet carrier with lacquered cast iron fitting, 4" (102) no hub waste and 2" (51) no hub vent connection, lacquered cast iron face plates and ductile iron foot supports, adjustable ABS nipple with integral test cap and neoprene bowl gasket, plated hardware, and polished cap nuts.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-10-27-37 (Specify L for left or R for right design) single, horizontal, adjustable, water closet carrier with lacquered, 37" (940) long barrel cast iron fitting, 4" (102) no hub waste, 2" (51) no hub vent connection, 2" (51) no hub auxiliary inlet connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts, and rear anchor tie down support.

  • Click for specsheet

    Click for downloads

    List Prices

     


    SPECIFICATION: MIFAB® Series MC-10D-27-37-HS double, horizontal, adjustable hub and spigot water closet carrier with lacquered, 37” (940) long barrel cast iron fitting, 2” (51) no hub vent connection, 2” (51) no hub auxiliary inlet connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

     

    Function:Used with back to back off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The 37” long barrel fitting eliminates the time and material required to install a battery of standard 13” long fittings. The auxiliary inlet is designed to receive waste from urinals and lavatories beside or opposite the closet carrier in order to reduce the amount of space required in the pipe chase. The closet carrier is completely concealed within the wall and supports the load of the fixtures through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixtures is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

     

    Note:14 1/2” (368) minimum space required between front of foot supports. 9” (229) minimum in wall space required between back of in wall foot supports.

     

    Note:Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-10D-27-37 double, horizontal, adjustable water closet carrier with lacquered with 37" (940) long barrel cast iron fitting, 4" (102) no hub waste, 2" (51) no hub vent connection, 2" (51) no hub auxiliary inlet connection, lacquered cast iron gasketed adjustable face plates, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors, and polished chrome plated finishing cap nuts.

  • Click for specsheet

    Click for downloads

    List Prices

     


    SPECIFICATION: MIFAB® Series MC-10D-27-37-HS double, horizontal, adjustable hub and spigot water closet carrier with lacquered, 37” (940) long barrel cast iron fitting, 2” (51) no hub vent connection, 2” (51) no hub auxiliary inlet connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

     

    Function:Used with back to back off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The 37” long barrel fitting eliminates the time and material required to install a battery of standard 13” long fittings. The auxiliary inlet is designed to receive waste from urinals and lavatories beside or opposite the closet carrier in order to reduce the amount of space required in the pipe chase. The closet carrier is completely concealed within the wall and supports the load of the fixtures through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixtures is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

     

    Note:14 1/2” (368) minimum space required between front of foot supports. 9” (229) minimum in wall space required between back of in wall foot supports.

     

    Note:Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-12 single, vertical, adjustable water closet carrier with lacquered cast iron fitting, 4" (102) no hub waste and 2" (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts, and read anchor tie down support.

  • Click for specsheet

    Click for downloads

    List Prices

     


    SPECIFICATION:MIFAB® Series MC-12-HS single, vertical, adjustable, hub and spigot water closet carrier with lacquered cast iron fitting, 2” (51) vent connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

     

    Function:Used when through the slab pipe connection is required with water closets installed on a common stack. Adjustable faceplate design permits installer to set water closet to the desired height from the finished floor, relative to the position of the vertical carrier fitting within the stack system. Typical for off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixture is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

     

    Note:11” (279) minimum space required between front of foot and rear of anchor support. 7 1/4” (184) minimum in wall space required between back of rear anchor support and back of in wall foot supports.

     

    Note:Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

     

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-12D double, vertical, adjustable water closet carrier with lacquered cast iron fitting, 4" (102) no hub waste and 2" (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors, and polished chrome plated finishing cap nuts.

  • Click for specsheet

    Click for downloads

    List Prices

     


    SPECIFICATION: MIFAB® Series MC-12D-HS double, vertical, adjustable hub and spigot water closet carrier with lacquered cast iron fitting, 2” (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

     

    Function:Used when through the slab pipe connection is required with back to back water closets installed on a common stack. Adjustable faceplate design permits installer to set water closets to the desired height from the finished floor, relative to the position of the vertical carrier fitting within the stack system. Typical for off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The closet carrier is completely concealed within the wall and supports the load of the fixtures through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixtures is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

     

    Note:14 1/2” (368) minimum space required between front of foot supports. 9” (229) minimum in wall space required between back of in wall foot supports. Note: Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

     

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-13 single, vertical, adjustable, water closet carrier with lacquered cast iron fitting, left, right or both (specify) 4" (102) side inlets, 4" (102) no hub waste, 2" (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted foot supports, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts, and rear anchor tie down support.

  • Click for specsheet

    Click for downloads

    List Prices

     


    SPECIFICATION: MIFAB® Series MC-13-HS single, vertical, adjustable, hub and spigot water closet carrier with lacquered cast iron fitting, left, right or both (specify) 4” (102) side inlets, 2” (51) vent connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

     

    Function:Used when one or two side inlets and through the slab pipe connection is required. Typical for water closets installed on a common stack to receive waste from the horizontal piping of MC-10 horizontal fittings or to receive waste from other plumbing fixtures with waste lines roughed in above the floor slab. Adjustable fitting and faceplate design permits installer to set the water closet to the desired height from the finished floor, relative to the position of the vertical carrier fitting within the stack system and the position of the horizontal waste piping from the horizontal carriers within the battery system. Typical for off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor.

     

    Note:11” (279) minimum space required between front of foot and rear of anchor support. 8 1/2” (216) minimum in wall space required between back of rear anchor support and back of in wall foot supports.

     

    Note:Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

     

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-13D double, vertical, adjustable closet carrier with lacquered cast iron fitting, left, right or both (specify) 4" (102) side inlets, 4" (102) no hub waste, 2" (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted foot supports, adjustable 8" tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors, and polished chrome plated finishing cap nuts.

  • Click for specsheet

    Click for downloads

    List Prices

     


    SPECIFICATION:MIFAB® Series MC-13D-HS double, vertical, adjustable hub and spigot water closet carrier with lacquered cast iron fitting, left, right or both (specify) 4” (102) side inlets, 4” (102) no hub waste, 2” (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

     

    Function:Used when one or two side inlets and through the slab pipe connection is required. Typical for back to back water closets installed on a common stack to receive waste from the horizontal piping of MC-10 horizontal fittings or to receive waste from other plumbing fixtures with waste lines roughed in above the floor slab. Adjustable fitting and faceplate design permits installer to set the water closets to the desired height from the finished floor, relative to the position of the vertical carrier fitting within the stack system and the position of the horizontal waste piping from the horizontal carriers within the battery system. Typical for off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixture is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

     

    Note:14 1/2” (368) minimum space required between front of foot supports. 9” (229) minimum in wall space required between back of in wall foot supports.

     

    Note:Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

     

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-14 single, vertical, fixed water closet carrier with lacquered cast iron fitting, 3" (76) or 4" (102) no hub waste (specify), and 2" (51) or 4" (102) no hub vent connection (specify), lacquered cast iron faceplate, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts, and rear anchor tie down support.

  • Click for specsheet

    Click for downloads

    List Prices

     


    SPECIFICATION:MIFAB® Series MC-14-HS single, vertical, fixed, water closet carrier with lacquered cast iron fitting, 4” (102) waste (specify), 2” (51) vent connection (specify), lacquered cast iron faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

     

    Function:Used with single water closets installed with the waste line below the floor slab. Common in hospitals, extended living and other facilities that have one water closet in each room. Can also be used within a horizontal battery of MC-10 fixture carriers if pipe space is limited and the horizontal wasteline can be installed below the floor slab. Typical for off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixture is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

     

    Note:8 1/2” (216) minimum space required between front of foot and rear of anchor support with 4” (102) waste fittings.

     

    Note:Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

     

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-15 single, vertical, fixed, water closet carrier with offset lacquered cast iron fitting, 4" (102) no hub waste and 2" (51) no hub vent connection, lacquered cast iron faceplate, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts, and rear anchor tie down support.

  • Click for specsheet

    Click for downloads

    List Prices

     

     


    SPECIFICATION:MIFAB® Series MC-15-hs single, vertical, fixed, water closet carrier with offset lacquered cast iron fitting, 4” (102) waste, 2” (51) vent connection, lacquered cast iron faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

     

    Function:Used with water closets that are offset from a common stack by 4” in multi-floor installations where minimum pipe space is required. Typical for off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixture is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

     

    Note:8” (203) minimum space required between front of foot and rear of anchor support.

     

    Note:Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

     

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-15D double, vertical, fixed water closet carrier with offset lacquered cast iron fitting, 4" (102) no hub waste and 2" (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors, and polished chrome plated finishing cap nuts.

  • Click for specsheet

    Click for downloads

    List Prices

     


    SPECIFICATION:MIFAB® Series MC-15D-HS double, vertical, fixed water closet carrier with offset lacquered cast iron fitting, 4” (102) waste, 2” (51) vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

     

    Function:Used with back to back water closets that are offset from a common stack by 4” in multi-floor installations where minimum pipe space is required. Typical for off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixture is more efficiently and economically maintained when installed off of the floor compared to floor mounted.

     

    Note:9 1/4” (235) minimum space required between front of foot supports.

     

    Note:Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.

     

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-21 floor mounted single, horizontal, adjustable water closet carrier without fitting, 4" (102) back outlet waste connection (specify no hub or threaded), lacquered cast iron adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts, and rear anchor tie down support.

    SPECIFICATION:
    MIFAB Series MC-22 floor mounted chair carrier with no hub or threaded 4" (102) outlet with adjustable lacquered cast iron face plate and ductile iron foot supports, adjustable ABS nipples with integral test caps and neoprene bowl gaskets, plated hardware, and polished cap nuts.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-24 residential water closet carrier with lacquered cast iron finish, 3" (76) PVC adapter, mounting hardware, threaded rod protectors, and polished chrome plated finishing cap nuts.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-25 residential water closet carrier system with lacquered cast iron no hub fitting (specify size and style), lacquered cast iron faceplate, mounting hardware, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, and polished chrome plated finishing cap nuts.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-26 water closet carrier with lacquered cast iron fitting, 4" (102) no hub waste, 2" (51) no hub vent connection, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts, and side anchor tie down support.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-27 water closet carrier with lacquered cast iron 90 degree double no hub stack fitting with 4" (102) no hub waste and anti-crossover baffles for floor mounted back outlet water closets. Complete with adjustable 8" ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors, polished chrome plated finishing cap nuts, and side anchor tie down supports.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-28 lacquered cast iron 90 degree double no hub stack fitting with 4" (102) no hub waste, 2" (51) no hub center vent connection, and anti-crossover baffles for floor mounted back outlet water closets.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-31 single lavatory hanger plate carrier with universal, adjustable top support plate. Complete with lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel feet and mounting hardware.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-31D back to back, lavatory hanger plate carrier with universal, adjustable, top support plates. Complete with lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel feet and mounting hardware.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-32 hanger plate carrier with universal, adjustable, top support plate and bottom bearing plate. Complete with lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel feet and mounting hardware.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-32D hanger plate carrier with universal, adjustable top support plates and bottom bearing plates. Complete with lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel feet and mounting hardware.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-33 hanger plate carrier with two universal, adjustable, top support plates. Complete with three lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel and mounting hardware.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-33-2 hanger plate carrier with two universal, adjustable top support plates and bottom bearing plate. Complete with three lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel feet and mounting hardware.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-34 single hanger plate and exposed arm lavatory carrier with universal, adjustable, top support plate and white, lacquered, adjustable, cast iron exposed support arms assembled to lacquered cast iron invertible and adjustable arm supporting brackets. Complete with two lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel feet and mounting hardware.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-34D back to back hanger plate and exposed arm lavatory carrier with two universal, adjustable, top support plates and four white, lacquered, adjustable, cast iron exposed support arms assembled to lacquered cast iron invertible and adjustable arm supporting brackets. Complete with two lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel feet and mounting hardware.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-35 hanger plate and exposed arm lavatory carrier with two universal, adjustable, top support plates and three white, lacquered, adjustable, cast iron exposed support arms assembled to lacquered cast iron invertible and adjustable arm supporting brackets. Complete with three lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel feet and mounting hardware.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-36, 22" x 4" lacquered steel plate with universal slots and six pieces of 1/4-20 x 8" long all threaded plated mounting studs, with nuts and washers.

    SPECIFICATION:
    MIFAB Series MC-36-2, 22" x 4" top lacquered steel plate, with universal slots and six pieces of 1/4-20 x 8" long all threaded plated mounting studs, and 22" x 2" bottom bearing plate with slots and two pieces of 5/16 x 10" long all threaded plated mounting studs, with nuts and washers.

    SPECIFICATION: MIFAB Series MC-37, 22" x 4" top front and back lacquered steel plates with universal slots and six pieces of 1/4-20 x 8" long all threaded plated mounting studs per plate, and 22" x 2" bottom front and back bearing plates with slots and two pieces of 5/16 x 10" long all threaded plated mounting studs per plate, with nuts and washers.

    SPECIFICATION: MIFAB Series MC-38D, 22" x 4" top front and back lacquered steel plates with universal slots and six pieces of 1/4-20 x 8" long all threaded plated mounting studs, per plate.

    SPECIFICATION: MIFAB Series MC-39D, 22" x 4" top front and back lacquered steel plates with universal slots and six pieces of 1/4-20 x 8" long all threaded plated mounting studs, per plate and 22.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-40 floor mounted exposed arm lavatory carrier with white, lacquered, adjustable cast iron exposed support arms. Complete with lacquered cast iron invertible and adjustable arm supporting brackets, alignment rod, two lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel feet and mounting hardware.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-40D floor mounted exposed arm lavatory carrier with back to back white, lacquered, adjustable cast iron exposed support arms. Complete with back to back lacquered cast iron invertible and adjustable arm supporting brackets, alignment rod, two lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel feet, and mounting hardware.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-41 floor mounted concealed arm lavatory carrier with lacquered, adjustable, ductile iron concealed support arms. Complete with lacquered cast iron invertible and adjustable arm supporting brackets, adjustable steel nipples with locknut and set screws, alignment rod, two lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel feet and fixture leveling and locking hardware.

  • Click for specsheet

    Click for downloads

    List Prices

     

    Part Number Configurator

    SPECIFICATION:
    MIFAB Series MC-41D floor mounted back to back concealed arm lavatory carrier with lacquered, adjustable, ductile iron concealed support arms. Complete with lacquered cast iron invertible and adjustable arm supporting brackets, adjustable steel nipples with locknut and set screws, alignment rod, two lacquered 2" x 1" x 1/8" thick structural steel uprights with 3" x 4-1/2" welded steel feet, and fixture leveling and locking hardware.

Returned 66 Results
Browse Pages :   1 | 2
Page 1 of 2
Downloads
MIFAB, Inc.
1321 West 119th Street Chicago, IL 60643
Toll Free: 800.465.2736
Tel: 773.341.3030
Fax: 773.341.3047
E-mail: sales@mifab.com